Universal universal remote control, copy remote control

2020-12-16 10:38:42

Friends who have worked outside the security gate know that the remote control of the electric door often fails. In fact, as long as we use it correctly, we can prevent the failure from happening! Here is an introduction to the use, matching method and code matching method of the electric door remote control.


Tools/Materials

Electric door remote control


MCU development, control board development, chip development, PCBA customization

Method/Step

How to use electric door remote control

A key: press A key to lock, fingerprint and door opening keys stop working, only the remote control can open the electric door

B key: Pressing the B key is to close the door, and also to unlock (press the A key to lock) the lock key

C key: press C key to open the door


Note:

1. When you get off work every day, first use the remote control to close the door, press the A button to lock the fingerprint switch outside the door, the inside switch and the inside infrared switch.

2. Insert the bolt lock into the floor tile hole on the right side of the electric door

3. When opening the door at work, you must first open the glass door on the west side of the corridor, enter the room and take out the lock on the right side of the electric door before using the electric door. Then use the remote control to press the B button to unlock it and you can use it normally.


Battery replacement method

When the remote control of the electric door is used frequently, the battery is prone to low or no electricity, which directly causes the remote control of the electric door to fail, and the electric retractable door cannot work normally. The following teaches you how to check whether the remote control of the electric door has less power and how to replace it:


 1. Long press the stop button, the lights on the electric door remote control are dim or flicker, the remote control distance becomes closer, and the remote control sometimes fails, etc., all due to insufficient battery power. Need to replace the battery in the remote control of the electric door


2. To replace the battery of the electric door remote control, unscrew the rear cover screw and remove the battery. The model is 1.5V3A. After replacing the new battery, try to press the door open or close button on the remote control. When it is normal, close the back cover. Tighten the screws.


When opening or closing the electric retractable door, if it is not because the remote control distance is too short, it is recommended not to pull out the antenna of the electric door remote control, because it is easy to damage the remote control of the electric retractable door and it is easy to get water.


 Simple copy method of electric door remote control

How to copy the electric door remote control? If you want to use the electric remote control you just bought, you need to confirm on the homepage that the remote control is good and there is no quality problem before copying normally. In addition, there is an understanding of the transmission frequency of the remote control. The technical term is called crystal value. In addition, you need to see the chip model in the manual. The specific copy method requires clearing and copying. The method is as follows:


MCU development, control board development, chip development, PCBA customization

1. Clear code

Press the remote control lock button and down button with both hands at the same time, at this time, the indicator light will flash continuously, and then release your hands, it means the clearing is successful. How to distinguish the remote control and clear it? As long as you simply press a button, the indicator light of the remote control turns on once it turns off, which means your operation is successful.


2. Copy

Take out the previous remote control, align the two remote controls, press and hold the door open button of the two remote controls at the same time with both hands, the indicator light will flash quickly, which means success. (Note that the remote control is best to be close, just like the Bluetooth and infrared transmission of the mobile phone, subject to the distance limitation), the copy method of the other three keys is the same as above, and you can proceed in sequence.


MCU development, control board development, chip development, PCBA customization

If you do not know how to use it, or if you still cannot use it normally according to the above methods, you can click on the homepage of Hefei Electric Door website and dial the contact information above. We will answer you in detail, provide free service, and treat people sincerely.


 Fixed code (learning code) matching of electric door remote control

 The appearance of the copy remote control makes the matching of the remote control of the electric remote control door very simple, and the matching of the fixed code remote control can be quickly completed in two easy steps.

(1) Features: No copy machine, no need to know the oscillation resistance, directly use the remote control to copy the remote control, it can be used immediately.

(2) Prerequisites for using this remote control

① The original remote control can be used and can be controlled normally.

②Need to know the frequency of the remote control c such as 390MHz, 400MHZ, etc.)

③The remote control chip is the following copyable chips SC2260/SC2262/HS2260/HS2262/PT2262/PT2260/EV15271SCL1527/SC5211/FP527/PT2240/HS2260/SC2240/HS1527/CL2262/HS2240/PT2264/LX2260/X2262/LP8527/HX2262 /HX2260 (Most fixed code and some learning code remote controllers on the market are compatible)

(3) Specific operation method

①Clear the code. Press the two buttons on the upper row of the remote control at the same time, the "door open" button and the "close door" button. The indicator light flashes once and then flashes quickly for about 2 seconds to indicate successful removal. After clearing, press the 4 buttons of the remote control, the indicator light flashes only once and then goes out.

② Duplicate. One hand is holding the original remote control and the other is holding the universal copy remote control. The two remote controls are as close as possible. Press the "Open" button on the two remote controls at the same time. The copy remote control indicator flashes quickly to indicate successful copying. , And then let go of your hand. Follow the same method in turn to copy the other three keys.

Note: If the light doesn't flash during copying, you can change the position, for example, put the heads of the two remote controllers facing each other and try to copy again. You can try a few more positions.

③Recovery. If the useful code is cleared by misoperation, you can press the two buttons on the bottom row of the remote control at the same time for 2 seconds before copying the other remote control again, and the indicator light flashes quickly to indicate successful recovery.


Coding method

1. Coding method

There are two types of coding methods commonly used in radio remote control, namely fixed code and rolling code. Rolling code is an upgraded product of fixed code. At present, rolling coding is used in all occasions that require confidentiality. The rolling code encoding method has the following advantages:

1. Strong confidentiality, the code is automatically changed after each launch, and others cannot use the code detector to obtain the address code;

2. The coding capacity is large, the number of address codes is greater than 100,000 groups, and the probability of using medium heavy codes is extremely small

3. Easy to code (see 3. How to configure the remote control for details), the rolling code has the function of learning and storing, without using a soldering iron, it can be coded at the user site, and one receiver can learn up to different transmitters , Has a high degree of flexibility in use;

4. The error code is small. Due to the advantages of coding, the error action of the receiver when it does not receive the local code is almost zero.


The fixed code encoding method has the following advantages and disadvantages:

1. The coding capacity of fixed codes is only 6561, and the probability of repeated codes is extremely high;

2. The code value can be seen through the solder joint connection method, or obtained by using a "code detector" at the site of use, so it has no confidentiality and is mainly used in occasions with low confidentiality requirements;

3. Because of its low price, it has also been widely used;


2. Remote control code matching method

If you can't buy the same model of remote control, you can install an external remote control system, general motors can be applied, and the installation is simple and the price is not high.


(1), fixed code remote control

Solder the pins corresponding to 0, 1, and 2 of the original remote control handle.


(Two), rolling code remote control

The rolling code remote control has a learning function. It does not need to be welded and can be operated directly on the garage door motor control panel, but note that the remote control must be of the same type. Different brands of garage door motors have different methods. (The following reference article for the code matching method is from the merchant blog and hope it will be useful to you)

1. Soma Motor

Press the "P" key four times and the indicator light 7 flashes, and then press the "+" indicator 7 to be steady. At this time, press any key of the remote control to be matched and the indicator light 7 will flash for two seconds, press the "P" key to save, and the other lights will always be on, and the matching is successful. To delete the remote control in use, that is, after the indicator light 7 is flashing, press "-" for 3 seconds, the indicator light 7 will change from steady light to flashing, and all remote control will be deleted, and then press the "P" key to save the mode and exit.

2. Zhongtian 800N motor (same as Barda)

Press and hold the P button for about 5-6 seconds until the No. 7 light is flashing (in this case, you can perform code matching and canceling operations). Decode: Press the "-" key for about 3 seconds, the No. 7 light turns from flashing to off, after releasing the button, wait for the No. 7 light to flash again, and the decoding is successful. Code matching: When the No. 7 light is flashing, press the "+" key once, and the No. 7 light will change from flashing to steady light, and then press the remote control operation key once, and the No. 7 light will change from steady light to flashing, press P Key to save, and the code is successful.

3. Zhongtian 600N motor:

Decoding: Open the case and find the code matching key and code matching indicator on the circuit board. Press and hold the code key for about 6 seconds until the indicator light goes out and the code elimination is complete. Code matching: Press and hold the code matching button on the circuit board for about 2 seconds, the code matching indicator light is always on, and then press the required code matching button on the remote control (except for the A or B, unlock key), the code matching indicator is switched from the normal Just turn bright.

4. Doorman

After the back cover is opened, the circuit board has: "remote control button", "code matching button" directly press to learn.

5. Hoth

Press the "S" key outside to learn.

6. Wright

There is a button behind the motor or in the lampshade. Click to learn.

7. Master

There is a red button behind the motor, press it to learn (there are three buttons "P" "+" "—"). First press the "p" key when the small red dot appears on the LED, press the up or down button of the remote control.

8. Old Spree

There is a button on the side of the motor, press it to learn.

9. Ideal, Juguang, Chibao, Somer, Changshun, New Honor:

Learning is done with the learning button in the motor.

10. American Lima

There was a big green button behind the early motors, press it to learn. (Press the new remote control twice), now there is a red button behind the motor, press it to learn. (Press the new remote control twice)

11. Old (new) Ono

The main frame is round (black and white is old; blue is new), logo: "OMNER", the original handle is Buick shape, and the letter "R" is pressed on the lower left foot. The two keys of the main machine position are the launch learning key and the distance learning key. To increase the handle, please press the launch learning setting.

The learning method is: press the launch learning button twice within 5 seconds, press any button of the remote control twice within one meter, the learning indicator flashes 3 times, and the learning is successful. Increase again, press the learning button again, press the remote control in turn. Up to 8 handles can be equipped.

12.Weston

Open the shell, there are 5 red lights and a button on the circuit board. Press the button 4 times and the fourth red light will light up. After long pressing the button, all five lights will light up. Press the remote control to pair the code.

13. Deutsche Mark

Motor English name: "MARANTECM" There are a total of 8 lights and three buttons on the main unit: "+" "—" "P", long press the P button and the lights are all on, press the remote control until the No. 7 light is on, press the remote control, and the learning is successful. Press P again to save and exit.

14. Jiahe

Press "K4" to check the code, press the remote control, and the learning is successful.

15. Hoth 350MHz

Remote control code matching press "S" button, you will hear the sound of Weng when you press the remote control. The code is successful.

16. Splet white:

Press the "SET" button repeatedly until the remote learning indicator lights up and the digital tube displays "L". Press the "+" key, the digital tube flashes slowly, indicating successful learning. Press the "+" key again to learn the next transmitter. After learning, press the "SET" key to exit the debugging state.

17. Speed F750

Press the small light in the lower right corner of K4 to light up, press the remote control to flash three times, the code is successfully matched.

18. Gude GD-7

Press the C button, the digital decimal will light up, press the upper left corner key of the remote control, the decimal point will go off, press the upper left corner key of the remote control again, the decimal will light up three times, and the code matching is successful.

19, extreme speed

There are four buttons K1, K2, K3, K4, just press K4 to pair the code.

20. New and old Changshun

Lao Changshun: Press the P button and the small red light is on. Press the remote control to learn successfully.

Xinchangshun: Press the P key and a small light will show that the remote learning is successful.

21. Master's new and old remote learning methods

A: Press a red button behind the motor, and then press the remote control. Learning is successful.

B: There are three buttons "P" "+" "—", first press the "p" button when a small red dot appears on the LED, press the up or down button of the remote control.

22. Brady

The matching of Brady's remote control: Press the LC button and then press any key on the remote control in your hand!

Clear code of Brady remote control: Press and hold the LC button for more than four seconds to clear the source code!

Brady start stroke adjustment: Press and hold the C button for more than 3 seconds, press the C button when the display door moves down to the position, and press the C button when the door moves up to a suitable place, the display H is set.

23. Giant Light

Remote control matching: There is a large button on the Juguang door opener to adjust the stroke. The learning button of the remote control is on the circuit board of the motor. We need to open the shell of the door opener, and you can see the learning remote control button on the circuit board. Press this button and then continuously press the remote control garage door. It means that the remote control has been learned.

Juguang Motor Type 688, 588 Stroke: Press and hold the setting button (J) for 3 seconds until the limited light flashes slowly (K), then press and hold the door open button (I) and let the door go to a suitable position, then the indicator light is fast After a few flashes, it will flash slowly, then press and hold the door open button (H) until the door is in a proper position and let go. After adjusting, press the setting button and then flash quickly for a few times and then flash slowly.

24 Yide

Yide remote control matching: first cut off the power and then connect it, press the K3 button and then press the remote control twice to complete the matching.

Yide’s stroke adjustment: Press and hold the K1 garage door and move it up to a suitable position. Press the upper limit of the remote control in your hand to complete the learning. Then release the k1 button. Then press and hold the K2 garage door and move it down to a suitable position by pressing the lower limit of the remote control in your hand to complete the learning. Then release the k2 key. The adjustment is complete.

25, Du Wen

The matching of the remote control: Press the P key once and then continuously press the remote control in your hand until the door moves (it may be necessary to press more than a dozen remote controls).

Stroke adjustment method 1: There are two buttons "+" and "-" on the Du Wen door opener, first press the + button and let go when the door moves up to a suitable position, press the lower limit of the remote control in your hand to complete the learning.

Stroke adjustment method 2: First press and hold the p key to learn that the lamp keeps flashing, then press the down key to the end, and then press the up key. Don't worry about it, just wait for the light to stop flashing.

26, Nice

Matching of Neos remote control: Press the code key to let go and press the remote control in your hand several times to complete the door movement learning.

Code clearing of Neos remote control: press and hold the code tube with indicator light to go out and clear code to complete.

27. Thinking SWIFT

The matching of the thinking remote control: press and hold the remote control and then press the S button of the motor for two seconds, then let go and the matching is successful.

Thinking remote control code clearing: Press and hold the S button, the indicator light goes out and the code clearing is completed after the indicator light is always on.

Mind door opener stroke adjustment: hold down the P key and the yellow light is always on, press the B key to move the door up to a suitable position and press the P key. Then press the A key and move the door down to a suitable position. Press the P key and the yellow light will flash twice and then go out. The adjustment is complete.

28.Kirin

Kylin remote control matching: press the code key to let go, and then press the remote control in your hand several times to complete the door movement learning.

Kirin remote control code clearing: press and hold the code key and wait for the indicator light to turn off to clear the code.

29. Bohai

Bohai remote control matching: press the code key to let go, and then press the remote control in your hand several times to complete the door movement learning.

Bohai remote control code clearing: press and hold the code key and wait for the indicator light to go out and clear the code

30. Mark

Press the P key for a few counts until the light is on, and the light is more than five meters away from the motor. Then press the remote control and the light flashes quickly, then press the P key to save the learning.

31. Ideal

Ideal remote control matching: Press the P key to let go, and then press the remote control in your hand a few times to complete the door movement learning.

Ideal remote control code clearing: press and hold the P key and wait for the indicator light to go out and clear the code.

32. Haitong

The matching of the Haitong remote control: first cut off the power and then connect it, press the P key of the door opener to let go, and then press the remote control in your hand several times to complete the door movement learning.

Haitong remote control code clearing: press and hold the P key and wait for the indicator light to go out and clear the code.

33.Sog

The matching of the SOG remote control: Press the code key to let go, and then press the remote control in your hand several times to complete the door movement learning.

SOG remote control code clearing: press and hold the code key and wait for the indicator light to go out and clear the code.

34, Pan'an

Press the learning button to let go, and then press the remote control in your hand a few times to complete the door move learning.

35. Maple Leaf

Maple Leaf remote control matching: press the code key to let go, and then press the remote control in your hand several times to complete the door movement learning.

Maple Leaf remote control code clearing: Press and hold the code key and wait for the indicator light to go out to clear the code.

36, ACDC

ACDC door opener remote control transmitter password clear: Keep pressing the red button "LEARN" on the control panel, the "LED1" light will turn on to off, indicating that the clearing is successful. After the password is cleared, the remote control transmitter can work, and it must be re-learned before it can be operated. In order to make your property safer, please clear the remote control password after installing the door opener, and then re-learn it.

Remote control transmitter learning: press the LEARN red button on the control panel, the "LED1" light is on, and then press the button of the remote control transmitter you want to use to complete the learning. At this time, this button can be used to operate the door. If you want to continue to learn the other buttons of the remote control transmitter, please repeat the above steps; if you want to add a transmitter, please repeat the above steps, and you can learn up to 25 transmitters. If LED1 turns on after 1 second, the transmitter fails to learn and needs to learn again.

Limit setting: Press the PRG red button on the control panel, the buzzer will sound, press and hold the button on the remote transmitter, the garage door will open, and the door will stop opening when the button is released; when the door is opened to the appropriate opening you think When setting, release the button of the remote control transmitter, press the red button of PRG at this time, the buzzer will stop ringing, the opening position will be automatically stored in the computer chip, the closing position will be confirmed, and the limit setting will exit. If the switch position setting is not ideal, you can repeat the above steps to reset.

37. Earth electric white steel telescopic door (rolling code):

Open the indoor manual control box, there is a button, press this button, there is a red light in the manual control box, press a few times, the red light of the remote control in your hand flashes and the remote control is matched.

38. Zijin

Press the code key and the indicator light turns on, release your hand and press the remote control continuously, and the learning is finished after the door moves.

39. Imported Soma

Press the remote control learning button, let go after the indicator light turns on, press the remote control continuously, and the learning is completed after the door moves.

If the original remote control is lost, for the sake of safety, the original remote control stored in the decoding chip must be cleared before the remote control is coded. If the operator is afraid that the code will not be correct, he can not clear it first, and then clear it after the code is correct. In this case, it is safe. Note that the original remote control is also re-coded.